Almost everyone seems to have his or her own piece of advice when it comes to Tools You Need to Install a New Bathtub .
:max_bytes(150000):strip_icc()/convert-tub-to-shower-4156975-05-db9a69eb718545759045e6e39b4cfacf.jpg)
Installing a bathtub isn't exactly rocket science, however it does call for solid plumbing, carpentry, and in some cases, tiling skills. Replacing an old tub with a brand-new one is additionally a reasonably hard project. If the old bathtub is conveniently easily accessible, the project can relocate quickly; if you have to open up a wall to remove the old bathtub and also place the brand-new tub, the job is much harder. In either instance, the project is within a residence handyman's abilities, although you will require an assistant to leave the old tub as well as set in the new one. Make certain you have actually qualified on your own for the task as well as are comfortable trying it. As opposed to hiring a specialist to take control of a halfway-completed job, it is much better to take into consideration utilizing one before you start. Possibilities are you might require an expert plumber to make tube connections.
This article will help you mount a brand-new tub in your restroom if you have already bought a new tub and don't need to alter the setup of your previous water supply pipes.
Your devices and also product list must comprise the following:
Removing Old Taps
If you need to replace old taps with new ones as a part of your installment, after that the first thing you must do is detach the water system. After doing so, switch on the taps to drain any water remaining in the system. The procedure of removing the existing faucets can be rather problematic due to the restricted access that is typically the case.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipelines to the taps. Have a towel ready for the remaining water that will originate from the pipelines. When the supply pipes have actually been removed, use the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary faucets from transforming throughout this procedure. When the taps have been gotten rid of, the holes in the bath/basin will certainly need to be cleaned of any old securing compound.
Prior to going on to fit the brand-new faucets, contrast the pipeline links on the old taps to the brand-new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new faucets to fit.
Suitable New Touches
If the tails of the brand-new taps are plastic, then you will certainly need a plastic adapter to prevent damages to the string. One end of the connector fits on the plastic tail of the faucet and also the other end supplies a link to the existent supply pipelines.
If you need to fit a monobloc, after that you will need decreasing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next, place the faucet in the installing hole in the bath/basin ensuring that the washers are in area between the tap and also the sink. Secure the tap in position with the manufacturer offered backnut. Once the tap is firmly in position, the supply pipes can be connected to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with regular tap ports. The previous type must be attached to the faucet ends initially, tightening up just by hand. The supply pipes can later be attached to the various other end. Tighten both ends with a spanner after both ends have been attached.
Mounting the Bathtub
Making use of the two wood boards under its feet, position the bathtub in the called for setting. The wooden boards are practical in uniformly spreading the weight of the tub over the location of the boards as opposed to concentrating all the weight onto 4 tiny points.
The following objective is to make sure that the bathtub is leveled all round. This can be attained by inspecting the level as well as adjusting the feet on the bathtub till the level reviews level.
To set up taps, fit the bottom of the outermost flexible faucet connector to the ideal supply pipeline by making a compression sign up with; then do the very same for the various other faucet.
Turn on the water and inspect all joints and new pipework for leaks and tighten them if necessary. Load the bath tub and also inspect the overflow electrical outlet and also the normal outlet for leakages.
Ultimately, fix the bath paneling as defined in the manufacturer's user's manual. Tiling and also sealing around the tub needs to wait until the bath tub has actually been used a minimum of when as this will certainly settle it into its last position.
Preparing for the Installation
Firstly, the sustaining frame supplied with the bath must be fitted (if required) according to the supplier's guidelines. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is essential to see to it that if the faucet includes a plastic washing machine, it is fitted in between the bathroom and also the taps. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets unit to avoid stress on the bath tub.
Fit the flexible tap adapters to the bottom of both taps utilizing 2 nuts and also olives (in some cases supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet through the hole in the bathroom. Utilize the nut provided by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bath. Ensure you make use of every one of the provided washing machines.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom ought to now prepare to be fitted in its last placement.
Tiling Around the Tub
In the area where the bathroom meets the tile, it is needed to seal the joins with a silicone rubber caulking. This is very important as the fitting can relocate enough to crack a stiff seal, causing the water to penetrate the wall surface between the bath as well as the tiling, leading to problems with wetness and feasible leakages to the ceiling below.
You can pick from a variety of coloured sealants to blend in your fixtures and also installations. They are sold in tubes as well as cartridges, and also are capable of sealing gaps as much as a size of 3mm (1/8 inch). If you have a larger gap to load, you can load it with twists of drenched newspaper or soft rope. Keep in mind to always fill the bath tub with water before securing, to allow for the activity experienced when the tub remains in usage. The sealer can fracture fairly early if you do not consider this activity before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are also quickly readily available on the market. It is suggested to fit the floor tiles making use of water-resistant or water-proof sticky as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We were made aware of that report about A Step-by-Step Guide to Installing a Bathtub through an acquaintance on a different site. Those who appreciated our blog posting please remember to pass it around. Thanks a bunch for your time. Visit us again soon.
Trusted service? Dial!